Kyoto2.org

Tricks and tips for everyone

Lifehacks

What are the settings on a hot tub?

What are the settings on a hot tub?

In general, the minimum temperature for most hot tub manufacturers is somewhere around 85° to 90° Fahrenheit. While most people feel comfortable with temperatures between 100° and 104° Fahrenheit, in the summers when it’s hot, you can set it at a lower temperature. Most heaters have settings as low as 80°.

How do I adjust the temperature on my Arctic Spa?

Setting Water Temperature Use the Up or Down Arrow button to regulate water temperature. The temperature setting will be displayed for 5 seconds to confirm your new selection. Water temperature can be adjusted by 1˚ increments from 59˚F to 104˚F (15˚C to 40˚C).

How do I know if Onzen is working?

Question 1: How do I know if the Onzen system is working? Conduct a “Sanitizer Production test” (Also known as a Smoke test). This procedure activates the Onzen System while de-activating the filtration pump so you can see the mist of gas bubbles produced by the Onzen System.

What is boost on Arctic Spa?

Use Arctic Pure, Boost to sanitize the water after heavy usage, or if the Chlorine Level is too low. Important: Always test and balance the pH and Chlorine levels before each spa use.

How do I reset my Arctic Spa hot tub?

Remove the spa cover and allow water to cool. At 41.7 the spa should automatically reset. If spa does not reset, shut off power to the spa and call your supplier for a service.

What do the buttons on a hot tub mean?

Some larger hot tubs may have up to three jet buttons on the control panel that allow you to adjust the speed and strength of your jets. In most cases, pushing the button the first time will turn them on a low setting and pushing it again will increase the speed.

What is standard mode on hot tub?

Standard (displays Std or St) The heating will come on whenever the water temperature drops below the thermostat set point, so the water will always be hot, and your hot tub will always be ready to use.

How can I make my hot tub hotter?

7 Hacks to Make Your Hot Tub Heat Up Faster

  1. Leave the cover on.
  2. Turn the jets on.
  3. Use a thermal spa blanket.
  4. Put a pop-up canopy tent around the tub.
  5. Wait for a warm day.
  6. Fill up with warm water.
  7. Use a portable immersion heater.

How do I reset my Arctic spa hot tub?

What is Onzen Arctic spa?

The Onzen™ Salt Water system is Arctic Spas® proprietary salt water system that produces sanitizer from Dead Sea salts through the process of electrolysis. Salt-water sanitizer generation has several advantages over traditional sanitizer methods.

What does Flo mean on Arctic Spa?

flow switch open
So your pump comes on low speed. This switch has a diaphragm side of it which is going to go up, close the contact between these two points. If it does not close the contact you’re going to get an FLO. which means flow switch open because the contacts have not closed.

What does salt water balance do?

The use of Salt Water Balance will help clear, prevent scale build-up, and increase bather comfort.

Why is my Arctic Spa not heating?

Spa does not heat: Check to see if the heat indicator is on or there are any error messages on the topside control panel. If the heat indicator is on and no error message appears contact your factory authorized dealer. Poor Jet Pressure: First check to see that the jet(s) are turned on fully.

What are the dials on a hot tub?

These controls are the dials on top of your spa that mix air with the water coming out of the jets. These valves allow cool air into the water, so if left on for long periods, your spa water will cool down and cause your heater to run more often.

What are the different hot tub modes?

Most Balboa hot tub control systems have three operating modes: standard, economy and sleep. These modes change at what time the hot tub heats, and therefore affect the overall power consumption.

What does SL on a hot tub mean?

Sleep
SL: Sleep – Similar to EC mode, the spa will only heat during the filtration cycles of the spa. Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.

Why is my hot tub not getting hot enough?

If the spa heater is not giving enough heat, it means a water flow problem from dirty filters or partially closed valves or clogged pumps. It could also be the spa cover allowing heat to escape.

How do I adjust the settings on my onzen spa?

So, to adjust your Onzen settings on a standard one-to-three pump spa that we offer, you’ll use the settings button. It’s the second one over on the bottom row.

Do I need to install a barrier around my Arctic spa?

Your Arctic Spa is equipped with a locking cover that meets the ASTM F1346-91 Standard for Safety Covers and as a result, is usually exempt from most barrier requirements.

Why choose Arctic Spas®?

Canadian built with the finest materials and advanced technology to withstand even the harshest of weather conditions, Arctic Spas® are made to perform… wherever you happen to live. To safely and effectively use your spa, we recommend that you take the time to read this manuaL before you hook-up and operate the spa.

How do you take care of your Spa when you have onzen?

I wanted to go over how you take care of your spa when you have an Onzen system. So, the very first thing that you do when you start up your tub, after doing a drain and refill, is add the Onzen salt. Most tubs are gonna take about three quarters of a bucket.

Related Posts