Tricks and tips for everyone


Why does my fireplace keep beeping?

Why does my fireplace keep beeping?

HOW OFTEN TO REPLACE? Your “beeping” fireplace is telling you something: It’s time to replace batteries! The receiving unit will need fresh batteries more frequently than the remote control. Change these batteries along with the batteries in your smoke alarms.

How do I stop my electric fireplace from beeping?

If your electric fireplace keeps beeping:

  1. Replace the batteries in the remote (if it has one).
  2. Ensure that the inlet and outlet to the heater aren’t being blocked.
  3. Ensure that the fireplace components are clean and working efficiently.

Why is my Skytech fireplace beeping?

When the ambient temperature at the thermistor (thermocouple), inside the receiver case cools down to between 130 deg. F to 120 deg. F the unit can be reset by turning the unit OFF then ON and the fireplace system will operate. However, the beeping will continue, if the ambient temperature remains between 120 deg.

How do I reset my electric fireplace?

SOLUTION: Turn all switches to the “off” position and unplug the unit from the wall for five minutes. After five minutes, power everything back on.

Should a gas fireplace make noise?

A gas fireplace should make little if any noise. If you hear new sounds – and especially if they’re happening in conjunction with operating problems – you need to look into it. Here are a few common noise problems: Dirty burners will often cause a sound similar to rumbling.

How do I change the bulb in my electric fireplace?

Electric Fireplace Light Bulb Replacement

  1. Begin by turning off your electric fireplace/insert.
  2. On the back of your electric insert you should find a Rear Access Panel.
  3. Locate and replace the light bulbs.
  4. Install your new bulb by screwing it in a clockwise motion.
  5. Secure the rear access door with the appropriate screws.

How do I reset my Skytech fireplace?

To reset the codes, simply press and hold the same “Learn” button for a solid 10-15 seconds after which you should hear consecutive beeps indicating the memory has been cleared.

Do electric fireplaces have a reset button?

If it’s still not turning on, try pressing the reset button on the unit. If that doesn’t work, you may need to call a technician. If your electric fireplace is turned on but it’s not getting hot, there could be an issue with the thermostat.

Why does my electric fireplace make noise?

One of the main causes of a vibrating sound coming from an electric fireplace is the fans motor. When the fans oscillating blades are in rotation, it can create a slow but continuous movement that has a jarring effect on parts located within your rear access panel. This causes nuts, screws, and bolts to come loose.

Why does my gas fireplace make a high pitched noise?

If the pilot light is improperly set, a whistling sound may be produced. Pilot lights for gas fireplaces should be kept on a low setting and gradually increased to light the flame. If the pilot light is kept on a high setting, the result is a flame in the fireplace along with an annoying whistling sound effect.

Why is my fireplace making noise when off?

Yes, a gas log system that makes a clicking or ticking sound when the burner is lit or turned off is typically caused by the metal shell around the gas logs contracting as it cools down. If the noise is excessive, then you will want to contact a qualified service technician.

Where is the bulb located in electric fireplace?

Where Is The Bulb In An Electric Fireplace? The bulb in an electric fireplace is typically located within the center of the unit. The access cover, typically located at the back of the unit, will need to be removed in order to reach the bulb.

Do all gas fireplaces have batteries?

Modern gas fireplaces more than likely have an intermittent pilot ignition system. This needs electricity to spark the pilot flame every time you go to use the fireplace. Many newer models, such as the Heatilator lines, have battery backup systems.

Do gas fireplaces take batteries?

Many gas fireplaces will work without electricity. You can run both intermittent pilot ignition fireplaces and standing pilot light systems during a power outage. IPI valve systems will normally have a backup battery system in place to ignite the flames.

Related Posts